(주)위슨테크놀로지 : 단방향AC

The iX Series II represents a new generation of AC and DC power source that addresses increasing demands on test equipment to perform more functions at a lower cost. By combining a flexible AC/DC power source with a high performance power analyzer, the iX Series II systems are capable of handling complex applications that have traditionally required multiple instruments.

The sleek integrated approach of the iX Series II avoids the cable clutter that is commonly found in AC test systems. The i/iX Series II is rackmountable with a 4U chassis design. All connections are made internally and the need for external digital multimeters, power harmonics analyzer and current shunts or clamps is completely eliminated. Using a state of the art digital signal processor in conjunction with precision high resolution A/D converters, the iX Series II provides more accuracy and resolution than can be found in some dedicated harmonic power analyzers. Since many components in the iX Series II are shared between the AC/DC source and the power analyzer, the total cost of the integrated system is less than the typical cost of a multiple unit system.

For less demanding applications, the Compact iX Series provides similar output and transient capabilities as the iX Series II, as well as basic measurements.

Features And Benefits
Key Features

3000 VA to 15000 VA of AC Output Power
Combines AC/DC source and power analyzer
Harmonic analysis of Voltage and Current
Programmable Impedance
AC, DC and AC+DC Output Modes
Multiple Chassis Configurations
Powerful output transient generation
High Crest Factor Capability
Arbitrary waveform generation
IEC 61000-3-2 and IEC 61000-3-3

Easy To Use Controls
Both the iX Series II and i Series II are microprocessor controlled and can be operated from an easy to use front panel keypad. Functions are grouped logically and are directly accessible from the keypad. This eliminates the need to search through various levels of menus and/or soft keys. A large analog control knob can be used to quickly slew output parameters. This knob is controlled by a dynamic rate change algorithm that combines the benefits of precise control over small parameter changes with quick sweeps through the entire range.

Applications
With precise output regulation and accuracy, the iX Series II AC and DC sources address many application areas for AC and DC power testing. The iX also provides a high load current capability, multi or single phase output modes, and built-in power analyzer measurements. Additional features including line distortion simulation (LDS), arbitrary waveform generation, and programmable output impedance address requirements for product quality and regulatory compliance testing.

Product Evaluation and Test
Increasingly, manufacturers of electronic equipment and appliances are required to fully evaluate and test their products over a wide range of input line conditions. The built-in output transient generation and readback measurement capability offers the convenience of an easy to use and integrated test system.

Avionics
With an output frequency range to 1000 Hz, at up to 150 VRMS, the iX Series II is well suited for aerospace applications. Precise frequency control and accurate load regulation are key requirements in these applications. The standard IEEE-488 control interface and SCPI command language provide for easy integration into existing ATE systems. Since the iX Series II can eliminate the need for several additional pieces of test equipment and only occupies 7 inches of rack space (4U), saving both cost and space. Instrument drivers for popular programming environments such as National Instruments LabView, DO-160, ABD-0100, MIL-STD-704A-F, and Boeing 7E73B-0147 are available to speed up system integration.

Regulatory Testing
As governments are moving to enforce product quality standards, regulatory compliance testing is becoming a requirement for a growing number of manufacturers. The iX Series II is designed to meet AC source requirements for use in Euronorm EN 61000 compliance testing. For flicker testing, the programmable output impedance capability of the 3001iX, 5001iX and 15003iX can be used to create the required IEC 725 reference impedance.

Multi-Box Configurations
For high power applications, two or three 5001i/iX chassis can be combined to provide 10 to 15 kVA of single or three phase power.

A 9003iX, 15003iX or 15003i three phase configuration can be ordered with the MODE-iX option. This option allows automatic switching between single or three phase output mode. In single phase mode, all current is available on phase A. The MODE-iX option switches the output from all three 5001i/iX amplifiers to a single output connector. Without the MODE-iX option, 15003i/iX systems are configured for three phase operation.

High Crest Factor
With a crest factor of up to 5:1, the i/iX Series II AC source can drive difficult nonlinear loads with ease. Since many modern products use switching power supplies, they have a tendency to pull high repetitive peak currents. The 5001iX can deliver up to 110 Amps of repetitive peak current (low range) to handle such loads.

Remote Control
Standard IEEE-488 and RS232C remote control interfaces allow programming of all instrument functions from an external computer. The popular SCPI command protocol is used for programming. Drivers for several popular instrumentation programming environments are available to facilitate systems integration of the i/iX Series II.

Instrument Control Software
Windows? Instrument Control Software is provided with the iX and i Series II. This software provides easy access to the power sources capabilities without the need to develop any custom code. The following functions are available through this GUI program:

Steady state output control (all parameters)
Create, run, save, reload and print transient programs
Generate and save harmonic waveforms [iX only]
Generate and save arbitrary waveforms [iX only]
Download data from a digital storage oscilloscope [iX only]
Measure and log standard measurements
Capture and display output voltage and current waveforms [iX only]
Measure, display, print and log harmonic voltage and current measurements [iX only]
Run IEC61000-4-11, IEC61000-4-14 and IEC61000-4-28 test programs
Display IEEE-488 or RS232C bus traffic to and from the AC Source to help you develop your own test programs.

Standard controller versions with single voltage range
Model	Output Power AC	Phase Output	Max Low V AC	Current Range DC
3001i/iX	3 kVA	1	22	15.6
5001i/iX	5 kVA	1	37	26
5001i/iX-400	5 kVA	1	37	26
9003iX¹	9 kVA	3	22	15.6
10001i/iX¹	10 kVA	1	74	52
10001i/iX-400¹	10 kVA	1	74	52
10002i/iX¹	10 kVA	2	37	26
10002i/iX-400¹	10 kVA	2	37	26
15001i/iX¹	15 kVA	1	111	78
15001i/iX-400¹	15 kVA	1	111	78
15003i/iX¹	15 kVA	3	37	26
15003i/iX-400¹	15 kVA	3	37	26

Model	Per Phase High V AC	Range DC	Input Voltage²
3001i/iX	11	7.8	208-240V
5001i/iX	18.5	13	208-240V
5001i/iX-400	18.5	13	400-480V
9003iX¹	11	7.8	208-240V
10001i/iX¹	37	26	208-240V
10001i/iX-400¹	37	26	400-480V
10002i/iX¹	18.5	13	208-240V
10002i/iX-400¹	18.5	13	400-480V
15001i/iX¹	55.5	39	208-240V
15001i/iX-400¹	55.5	39	400-480V
15003i/iX¹	18.5	13	208-240V
15003i/iX-400¹	18.5	13	400-480V
Note (1) Supplied with System Interface cable(s). Controller in master unit only. Note (2) All input voltage specifications are for Line to Line three phase except 3001iX and 9003iX which require single phase input only. Note (3) For 10002iX split phase system specifications, refer to 5001iX for each phase.

Options
-400	400-480 Volt Line to Line AC input.
-411	IEC61000-4-11 test firmware. See also EOS1/3.
-413	IEC61000-4-13 Harmonics and Interharmonics test firmware.
-EOS-1	IEC61000-4-11 Electronic Output Switch (1 phase) Includes -411 option. Refer to EOS data sheet for details.
-EOS-3	IEC61000-4-11 Electronic Output Switch (3 phase) Includes -411 option. Refer to EOS data sheet for details.
-LKM	Clock/Lock Master
-LKS	Clock/Lock Auxiliary
-LNS	Internal AC Line Sync.
-FC	Modifies output frequency control to ± 0.25%
-MODE-iX	Switches between 1 and 3 phase output modes, for 9003iX or 15003i/iX only.
OMNI-1-18i	Impedance matching network for single phase 3001i/iX or 5001i/iX to support IEC-1000-3-3 flicker tests.
OMNI-3-18i	Impedance matching network for three phase 9003iX or 15003i/iX systems to support IEC-1000-3-3 flicker tests.
OMNI-3-37i	Impedance matching network for three phase 30003i/iX systems to support IEC-1000-3-3 flicker tests.
-RMS	Rackmount Slides
-WHM	Watt-Hour Measurement option
-XLS	External AC Line Sync adaptor. (-LNS and XLS are mutually exclusive)
Cabinets	Multi box iX Series II systems can be factory installed and wired in 19 inch cabinets. Cabinet configurations can be ordered by preceeding the model number with a “C1-C4” prefix. Contact factory for pricing and details.

Avionic Test Routine Options
-ABD	Airbus Directive 0100.1.8 tests
-AMD	Airbus AMD24 tests.
-A350	Airbus A350 tests.
-AIRB	Airbus test package (A380, A350, AMD24)
-B787	Boeing 787B3-0147 tests
-160	RTCA/DO-160D and EUROCAE test firmware. Refer to -160 option data sheet for details.
* Note Reference the Avionics Test User Manual P/N 4994-971 for a complete listing of performance capabilities.

Feature Comparison
Controller	i	iX
AC mode	x	x
DC mode	x	x
AC+DC mode	-	x
Transient programming	x	x
Arbitrary waveforms	-	x
Measurements	x	x
Harmonic measurements	-	x
Waveform acquisition	-	x
Programmable Impedance	-	x
IEEE / RS232	x	x

California Instruments i-iX Series II : Diagram

Diagram Formats
PDF	California Instruments i-iX Series II Diagram (91KB)

다운로드

등록된 자료가 없습니다.

i / iX Series II User Manual Rev W

i & iX Series SCPI Programming Manual Series I / II Rev AB

i Series / iX Series User Manual Rev Z

Avionics Software Manual

CI Virtual Panels Avionics Software Manual, 4994-972 Rev A

AC 전원공급기 (KC인증)

California Instruments i-iX Series II : Diagram